Power supply for ceiling and truss tracking areas

Power supply for ceiling and truss tracking areas

The switched-mode power supply has a metal case and is designed to provide power to the ceiling and truss tracking areas.

Ease of use

The switched-mode power supply comes in a standard metal case that is designed for surface mounting. The device features compact dimensions, reduced no-load consumption, universal input voltage range, wide operating temperature range, and short circuit, overcurrent, and overvoltage protection. The heat is dissipated by natural convection.
Features of the power supply:
The maximum number of reference bars that can be connected to the power supply is 27 pcs. for a ceiling tracking area and 36 pcs. for a truss tracking area. Wherein no more than 9 and 12 pcs. are allowed to be connected to each output respectively.

Device Mounting Requirements

Before starting installation or maintenance of the power supply, disconnect the device from the mains and the tracking area.
Make sure that the power supply cannot be accidentally reconnected to the mains!
Ensure good ventilation for the device to avoid overheating. The distance to heat sources should be at least 10-15 cm.

Overview and mounting dimensions

Overview and mounting dimensions with brackets

Default kit

The default configuration for the ceiling tracking area includes only the switched-mode power supply.
The default kit for the truss tracking area includes the following items:
If the installation of your tracking area requires a complete set, please let sales managers know.

Plugs and connections

The power supply is equipped with an AS-216-EN input connector with a switch and three KF2EDGWB-5.08 output connectors.
To connect IR markers of a ceiling tracking area to a power supply you will need:
Strictly observe the polarity of the IR marker connection to avoid damage! It is forbidden to connect or disconnect IR markers while the power supply is running!
H05VV-F 2x1.5 cable, included in default kit, is used to connect truss tracking area to a power supply. It is necessary to insert the cable with the mating part into the KF2EDGWB-5.08 connector and fix it with two screws built into the pluggable terminal block.
The other cable end is inserted into the GX16 connector of the reference bar and tightened with a fixing nut.
It is forbidden to connect or disconnect reference bars while the power supply is running!

Installation options

The power supply is used with a truss or a ceiling tracking area. In the first case, the power supply is mounted onto the truss segment using special brackets with elastic mountings.
For a ceiling tracking area, the device is mounted onto a rigid surface (walls, columns) in the vicinity of the ceiling tracking area.

Technical specifications

Output
DC voltage
18 V
Current
10-15 А
Rated power
270 W
Ripple & noise (max)
<700 mVp-p
Voltage tolerance
±2.0%
Line regulation
±0.5%
Load regulation
±5.0%
Setup, rise time
2000 ms, 100 ms/230 VAC under full load
Input
Voltage range
210-230 VAC
Frequency range
50-60 Hz
Current
4 А
Efficiency
83%
Inrush current
Cold start 65 A/230 VAC
Leakage current
<0.75 mA/277 VAC
Protection
Overload
130-185% rated output power. Protection type: hiccup mode, recovers automatically after fault conditions are removed
Overvoltage
13.6-16.3 V. Protection type: shut down o/p voltage, re-power on to recover
Overheating
95°С±5°С (RTH2). Protection type: shut down o/p voltage, recovers automatically after temperature goes down
Safety and standards
Standards
EN61347-1; EN61347-2-13; SELV; IP60 approved
Withstand voltage
I/P-O/P: 3.75 KVAC I/P-FG: 2 KVAC O/P-FG: 0.5 KVAC
Isolation resistance
I/P-O/P, I/P-FG, O/P-FG: 100 MOhms/500 VDC/70% RH
EMC emission
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
EMC immunity
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A
Others
MTBF
>216.3 Khrs min, MIL-HDBK-217F (25°C)
Operating temperature
-30°C — +70°C
Humidity
20-90% (+25°C), RH non-condensing
Package size
280 × 95 × 50 mm
Package weight
1.9 kg
To operate the power supply in regions with a mains voltage of 100-127VAC, a converter is required!